Military Armaments Corporation * A new company at Stephenville, Texas, using an old, yet recognized name, was started up there. A semi-auto carbine weapon was also made and, like the pistol, it was designed in such a manner as to be not converted to full auto fire. A second chambering was offered in a conversion kit to allow the pistol to fire. This closed bolt pistol was chambered in 9 mm. To increase sales, a semi-auto ONLY pistol version was also built which fires from the closed bolt and was designed NOT to be converted to full auto fire. Produced in 9 mm only, it was made as an open bolt firing submachine gun.
#Mac 11 for sale full auto mac#
As most of the principals of this new company were managers and partners of the other company, the organization produced an Ingram-styled submachine, which was on the drawing boards at the MAC / RPB prior to the change in management. * This company was a spin-off of sorts from R.P.B. Are these receivers some of the un-built Jersey arms submachine guns or just stray pistol receivers from Patriot Distribution? Which ever they are, today they can ONLY be assembled as closed bolt firing guns. ***Every now and again, a stripped lower receiver marked Jersey Arms will appear on the secondary market. These pistols were of course semi-auto firing, closed bolt design guns which saw limited sales and are seldom seen on the market today. ***Starting in the late 1980's the Patriot Distribution Company of Pennsylvania offered a pistol chambered in 45 acp based on the Jersey Arms design. NOTE: this was the last production of the new submachine guns that could be legally sold in this country. The approved Jersey arms receivers, which could not be sold over seas nor at home, were stored for years until their sale to R.P.B., who reworked the submachine guns using MAC parts, and then offered the registered submachine guns for sale to U.S. However the State Department stopped all such sales for fear the U.S. A large order was obtained to arm the Afghanistan rebels. After 4+ years of reworking, the Avenger was finally approved for sale. Their submachine guns and pistols were designed to use the M3 magazine, larger rear and front sights, and take down pin that incorporates a large pull ring to aid in the disassembly of the weapon. No matter how the weapon was redesigned, the ATF would not allow production. The Avenger, as their model was called, however had the same problem as the R.P.B. Te design was reworked, and in some ways there were improvements. * was founded in New Jersey on the principal that if the original MAC was good, their version would be better. Not long after, this firm ceased operations. RPB Industries made, (for a short time only), a closed bolt firing M10 in 9 mm. All open bolt firing weapons made after June 1982 were to be reclassified as submachine and subject to NFA rules. Other markings include sap M10, sap M11, and sac M10, (c=carbine). This firm also produced open bolt firing PISTOLS in the same calibers as the submachine guns. RPB iNDUSTRIES * made OPEN bolt submachine guns, (M10 & M11), in 9 mm, 45 acp, and.
There are reports of a few semi-auto pistols being produced to date only one has been documented. All but a few experimental guns were made to fire from the OPEN bold position. They also made compact submachine guns in. * made submachine guns in 9 mm and 45 acp, (Model 10). When required, compensation will be accepted in the form of personal checks, money orders, federal reserve prommmissory notes, and in the not-too-distant future.credit cards. All transmissions and communications are considered PRIVILAGED. Parts, Maintenance Data, Accessories, Technical Details, and related information can be obtained by transmitting inquiries to: by landline:Īll requests should have a speedy reply subject to operational scheduling.
style firearm via e-mail or by prearranged phone conference. **Questions? I am willing to answer your inquiries about your particular M.A.C. With over 34 years of experience in the defense industry, and as one of the few surviving business and design associates who worked with Gordon Ingram and others, I am in a unique position to offer the experience necessary for the specialized care and proper maintenance of the Ingram designed weapons and the many clones (both pistols and carbines) offered by the various manufactures.
0 kommentar(er)
